Lsi sas2008 firmware download ubuntu 14.04
![lsi sas2008 firmware download ubuntu 14.04 lsi sas2008 firmware download ubuntu 14.04](https://media.bkns.vn/uploads/2018/09/lsi-megaraid-9211-8i.jpg)
- #LSI SAS2008 FIRMWARE DOWNLOAD UBUNTU 14.04 HOW TO#
- #LSI SAS2008 FIRMWARE DOWNLOAD UBUNTU 14.04 INSTALL#
- #LSI SAS2008 FIRMWARE DOWNLOAD UBUNTU 14.04 ARCHIVE#
- #LSI SAS2008 FIRMWARE DOWNLOAD UBUNTU 14.04 ISO#
Also no need to set SAS address if it’s the only card in the server.įor what concerns your case, I’d try to flash it to the Dell firmware first (any of your choice, for H200I, H200A or with the 6GBPSAS.fw). No need to flash BIOS (-b flag) if not going to boot from that controller.
![lsi sas2008 firmware download ubuntu 14.04 lsi sas2008 firmware download ubuntu 14.04](https://www.legitreviews.com/wp-content/uploads/2014/03/adata-SP900.jpg)
#LSI SAS2008 FIRMWARE DOWNLOAD UBUNTU 14.04 INSTALL#
I used megarec to wipe the card first before it would let me install that firmware.I finally found the wise words from fourlynx on this homelab reddit discussion on the final song and dance I had to perform to get my Dell H200 card to work with the LSI firmware I wanted With both utilities working I was still having trouble with sas2flash erroring out on me. My final resort: an even older desktop (my Dad’s old PC, circa 2008.) It did the deed! FINALLY Instructions per this page were to boot to EFI and run the flash utilities there, but that desktop didn’t have an EFI shell and I couldn’t get it to boot one from USB. Comically, my desktop had a chipset that caused sas2flash not to work!! It would fail with the message
![lsi sas2008 firmware download ubuntu 14.04 lsi sas2008 firmware download ubuntu 14.04](https://pg-cdn-a2.datacaciques.com/00/MjUxMzA2/20/06/11/l8set63isq2en0c5/3d8e4f062ad01ffe.jpg)
I ended up taking the card out and putting it into my desktop to run megarec commands. I very frustratingly found I couldn’t use the megarec utility on my Dell server megarec would simply hang I was able to find the megarec utility here.
#LSI SAS2008 FIRMWARE DOWNLOAD UBUNTU 14.04 HOW TO#
I found this guide on how to use the megarec utility to wipe the firmware in order to flash over properly. "Cannot Flash IT Firmware over IR Firmware". I tried following the instructions as laid out here but I was met with this lovely message: It was very frustrating to flash, however. I found better firmware to flash in order to fix it. I had some issues with my 4tb+ drives dropping out of my zpools. Broadcom offers a neat utility called the LSI pre-boot USB tool that I didn’t end up using: I didn’t end up using it but in my internet travels I came across this. Reboot, and finally, after hours of banging my head on the wall… success!!! These 4 drives were only being reported as 2TB before Sas2flsh -o -sasadd 5xxxxxxxxxxxxxxx (replace this address with the one you wrote down in the first steps). Sas2flsh -c 0 -list #Write down the SAS Address and continue to the next steps. Sas2flsh -listall #Use the number in the first column to get the SAS Address for the card. I didn’t care about IT mode (my card is not a RAID card) but it had the information I needed. My savior was this writeup on how to flash certain versions of these cards to IT mode. If you simply run flash.bat you’ll be greeted with a message saying no compatible adapters were found. I got so far and yet tripped at the finish line.
#LSI SAS2008 FIRMWARE DOWNLOAD UBUNTU 14.04 ISO#
Then follow the instructions linked to above of downloading a freeDOS ISO, extracting it to the same folder you extracted the firmware to, then running the command to build your ISO (adjust as needed) mkisofs -o First, download the Windows installer, open with your archive program of choice and extract to the folder you’re going to build your ISO from. To flash this I chose to create a bootable dos ISO as per the instructions here. – Added support for SAS HDDs larger than 2TB After hours of digging around in unholy corners of the internet I finally arrived on this Dell Support page. I later found the model number of my card – Dell PERC H200E – which proved to be quite vital information. Lspci revealed this card uses the LSI SAS2008 chipset, which from what I’ve read is capable of drives greater than 2TB in size. I was clearly running into some sort of firmware issue. Well, they sort of showed up – they all reported capacities of exactly 2TB. When I plugged everything in, to my dismay none of my disks with greater than 2TB capacity showed up. The plan was to create a DAS device from my old NAS chassis and have it be driven by my new storage server (new to me anyway – a Dell PowerEdge R610.) I ordered what was listed simply as “ Dell SAS External Dual Ports PCI-E 6GB/S Host Bus Server Adapter 12DNW 342-0910 Consumer Electronics” from Amazon for $40 to accomplish this goal. I just recently got a $40 external SAS adapter for my new storage server.#LSI SAS2008 FIRMWARE DOWNLOAD UBUNTU 14.04 ARCHIVE#